UMI-77 is a selectiveMcl-1inhibitor, which shows high binding affinity toMcl-1(IC₅₀=0.31 μM). UMI-77 binds to the BH3 binding groove ofMcl-1withK_iof 490 nM, showing selectivity over other members of anti-apoptoticBcl-2members.

Competitive binding curve of UMI-77 against Mcl-1 is obtained by FP based binding assay using fluorescent labeled Bid BH3 peptide with an IC₅₀of 1.87±0.22 μM. UMI-77 potently inhibits the cell growth of BxPC-3 and Panc-1 cell lines with IC₅₀values of 3.4 μM and 4.4 μM respectively, and shows 3 to 5 times less potency in inhibition of the cell growth of two other tested cell lines MiaPaCa-2 (12.5 μM) and AsPC-1 (16.1 μM). The cell growth inhibition potency of UMI-77 correlates with the highest expression of Mcl-1 and Bak, and lowest expression of Bcl-xL in the sensitive cell lines, BxPC-3 and Panc-1. Capan-2 cells are showing similar sensitivity to UMI-77 (IC₅₀of 5.5 μM) as BxPC-3 and Panc-1, although has low Mcl-1 levels^[1].

UMI-77 exhibits moderate metabolic stability with a half-life of 45 minutes.The maximum tolerated dose (MTD) of UMI-77 in SCID mice is determined. Administered 60 mg/kg i.v. for 5 consecutive days per week for two weeks does not cause any loss in the animal weight and there is no obvious sign of toxicity during the course of the treatment. Increasing the dose to 80 mg/kg show severe animal weight loss (>20%), therefore 60 mg/kg is used as a therapeutic dose for the in vivo efficacy studies. Daily treatment with UMI-77 for 5 consecutive days a week for two weeks results in statistically significant tumor growth inhibition by 65% and 56% in comparison with the controls in day 19 (p<0.0001) and day 22 (p<0.003) respectively^[1].

468.34

Solid

C₁₈H₁₄BrNO₅S₂

518303-20-3

Room temperature in continental US; may vary elsewhere.

DMSO : ≥ 28 mg/mL(59.79 mM)

*"≥" means soluble, but saturation unknown.

请根据产品在不同溶剂中的溶解度选择合适的溶剂配制储备液；一旦配成溶液，请分装保存，避免反复冻融造成的产品失效。
储备液的保存方式和期限：-80℃, 6 months; -20℃, 1 month。-80℃ 储存时，请在 6 个月内使用，-20℃ 储存时，请在 1 个月内使用。

请根据您的实验动物和给药方式选择适当的溶解方案。以下溶解方案都请先按照In Vitro方式配制澄清的储备液，再依次添加助溶剂：

——为保证实验结果的可靠性，澄清的储备液可以根据储存条件，适当保存；体内实验的工作液，建议您现用现配，当天使用； 以下溶剂前显示的百
分比是指该溶剂在您配制终溶液中的体积占比；如在配制过程中出现沉淀、析出现象，可以通过加热和/或超声的方式助溶

• 1.

  请依序添加每种溶剂： 10% DMSO    40%PEG300   5%Tween-80   45% saline

  Solubility: ≥ 2.5 mg/mL (5.34 mM); Clear solution

  此方案可获得 ≥ 2.5 mg/mL (5.34 mM，饱和度未知) 的澄清溶液。

  以 1 mL 工作液为例，取 100 μL 25.0 mg/mL 的澄清 DMSO 储备液加到 400 μL PEG300 中，混合均匀；向上述体系中加入50 μL Tween-80，混合均匀；然后继续加入 450 μL生理盐水定容至 1 mL。

  将 0.9 g 氯化钠，完全溶解于 100 mL ddH2O 中，得到澄清透明的生理盐水溶液
• 2.

  请依序添加每种溶剂： 10% DMSO    90% (20%SBE-β-CDin saline)

  Solubility: 2.5 mg/mL (5.34 mM); Suspended solution; Need ultrasonic

  此方案可获得 2.5 mg/mL (5.34 mM) 的均匀悬浊液，悬浊液可用于口服和腹腔注射。

  以 1 mL 工作液为例，取 100 μL 25.0 mg/mL 的澄清 DMSO 储备液加到 900 μL20% 的 SBE-β-CD 生理盐水水溶液中，混合均匀。

  将 2 g 磺丁基醚 β-环糊精加入 5 mL 生理盐水中，再用生理盐水定容至 10 mL，完全溶解，澄清透明